- ADDRESS：Jinan City, Shandong Province
- Wanda Plaza, Jinan, Shandong, China
- +8617615809553
- info@deruna.com
The WG1664230053/2 Plastic Lamp Shade is a high-quality, impact-resistant lighting cover designed specifically for SINOTRUK Howo heavy-duty trucks. As a trusted supplier of genuine Sinotruk howo parts, we offer this OEM-grade lamp shade as a direct replacement for the original factory component. The WG1664230053/2 lamp shade provides reliable protection for the vehicle’s front or rear lighting units, shielding bulbs and reflectors from moisture, dust, stones, and road debris while maintaining optimal light transmission. Manufactured from high-grade polycarbonate with UV-blocking additives, this shade resists yellowing, cracking, and hazing even after years of exposure to intense sunlight and extreme weather conditions.
The WG1664230053/2 plastic lamp shade is engineered to preserve the brightness and beam pattern of the original lamps, ensuring that your truck remains visible and compliant with road safety regulations. Its precise fitment and durable construction make it an essential replacement part for maintaining both safety and aesthetics.
OEM direct replacement • UV-stabilized polycarbonate • Impact & scratch resistant • Easy snap-fit installation
The WG1664230053/2 is a plastic lamp shade (also referred to as a lens cover or light housing) designed for the SINOTRUK Howo A7 and T7H series trucks. It serves as the protective outer cover for the front combination lamps, rear tail lights, or auxiliary lighting units, depending on the specific vehicle configuration. This OEM-grade shade replicates the original part’s curvature, mounting clips, and optical clarity, ensuring a perfect fit and consistent light output after replacement.
Constructed from high-impact polycarbonate with a hard-coat scratch-resistant layer, the WG1664230053/2 offers superior durability against stone chips, minor abrasions, and chemical exposure. Its transparent (or lightly smoked) finish maintains high light transmittance, allowing the full brightness of the bulb to reach the road while protecting the internal reflector from dust and moisture ingress.
The shade is also designed with UV-absorbing additives that prevent yellowing and clouding over time – a common issue with inferior aftermarket covers. By maintaining optical clarity, the WG1664230053/2 ensures that turn signals, brake lights, and headlights remain highly visible, reducing the risk of rear-end collisions and enhancing overall road safety.
This lamp shade is interchangeable with earlier part numbers (WG1664230053/1) and is a popular choice for collision repairs, UV-damage replacements, or fleet-wide lighting upgrades. Its lightweight yet robust design reduces the risk of shattering in the event of minor impacts.
The WG1664230053/2 Plastic Lamp Shade is engineered for SINOTRUK Howo A7 and T7H series trucks, including models ZZ4257, ZZ3257, and other variants with compatible front or rear lighting housings. It is a direct replacement for the original lamp cover and is also backward-compatible with the earlier revision WG1664230053/1.
This cover is commonly used in combination with the main headlight unit, turn signal assembly, or rear combination lamp. Its universal clip pattern fits most OEM lamp housings, making it suitable for both left-hand and right-hand drive configurations. The WG1664230053/2 is also a popular choice for aftermarket lighting upgrades where the original cover is damaged or lost.
In heavy-duty applications such as long-haul transport, mining, and construction, the lamp shade is constantly exposed to flying stones, insects, and harsh chemicals. The WG1664230053/2 is designed to withstand these elements, preserving the integrity of the lighting system and ensuring continuous compliance with road safety regulations.
When replacing a cracked or yellowed shade, always verify the lamp type (LED or halogen) and the housing dimensions, although the WG1664230053/2 fits the vast majority of Howo A7 and T7H lamp assemblies. For fleets, this part simplifies inventory by covering multiple lamp positions with a single SKU.
Replacing the WG1664230053/2 lamp shade is a simple, tool-free procedure that typically takes under 5 minutes. Begin by opening the hood (for front lamps) or accessing the rear lamp housing from the outside. Locate the retaining clips on the existing shade – these are usually visible as small tabs around the perimeter.
Gently press the clips inward while pulling the shade outward. If the shade is stuck due to dirt or rubber seal adhesion, use a plastic trim tool to carefully pry it loose without damaging the housing. Once removed, clean the lamp housing with a soft cloth to remove dust and debris.
Align the new WG1664230053/2 shade over the housing, ensuring that the clips line up with their corresponding slots. Press firmly around the entire perimeter until you hear each clip snap securely into place. Verify that the shade sits flush and that no gaps exist between the shade and the housing.
For maintenance, regularly wash the shade with mild soap and water to remove road grime and insect residue. Avoid using abrasive cleaners, solvents, or pressure washers at close range, as these can damage the hard coat. If the shade becomes scratched, light polishing with a plastic-safe compound can restore clarity.
Inspect the shade periodically for cracks, clouding, or loose clips. A damaged shade should be replaced immediately to protect the lamp internals and maintain proper light output. The WG1664230053/2 is designed for long service life, but harsh environments may accelerate wear.
The WG1664230053/2 Plastic Lamp Shade is manufactured in an ISO 9001-certified facility using precision injection-molding processes. The raw polycarbonate resin is sourced from leading global suppliers and compounded with proprietary UV stabilizers and impact modifiers to meet SINOTRUK’s demanding specifications.
Each shade undergoes a series of quality checks, including optical clarity measurement (haze & transmission), UV aging tests (3000 hours accelerated), and impact resistance testing per SAE J575. The clip retention force is also verified to ensure that the shade stays securely attached even under severe vibration.
We back the WG1664230053/2 with a comprehensive warranty against material and workmanship defects. Our rigorous quality control ensures that every shade delivers the same optical performance and durability as the original factory part, giving you confidence in your truck’s lighting reliability.
Choose genuine quality for your lighting repairs – choose the WG1664230053/2 Plastic Lamp Shade.
The WG1664230053/2 Plastic Lamp Shade is a small but critical component that directly impacts your truck’s safety, visibility, and legal compliance. A cracked, yellowed, or missing lamp shade can reduce light output, scatter the beam, and allow moisture to damage the bulb and reflector – leading to failed inspections and increased collision risk.
By replacing it with this genuine OEM-grade shade, you restore the original light intensity and beam pattern, ensuring that your turn signals and brake lights are clearly visible to other road users. The UV-stabilized material prevents the clouding that plagues cheap replacements, keeping your truck looking professional for years.
Fleet operators will appreciate the quick, clip-on installation that reduces labor time and minimizes vehicle downtime. Owner-operators will value the peace of mind that comes with a part that meets ECE safety standards and fits perfectly the first time.
Invest in the WG1664230053/2 Plastic Lamp Shade and protect your SINOTRUK Howo’s lighting system with the same quality that the manufacturer intended. Its optical clarity, impact resistance, and weather-sealing design make it the intelligent choice for drivers who refuse to compromise on safety.
Order your WG1664230053/2 today and ensure your HOWO truck remains road-legal, visible, and ready for any journey ahead.
We are a first-class heavy duty vehicles and spare parts supplier in China. which covers from engine, gearbox, cab, axle assemblies to main assembly accessories, electrical parts and other chassis parts like brake, clutch and steering parts.
A PROFESSIONAL CHINA TRUCK AND SPARE PARTS SUPPLIER
@Copyright DERUNA
