- ADDRESS：Jinan City, Shandong Province
- Wanda Plaza, Jinan, Shandong, China
- +8617615809553
- info@deruna.com
The WG295420033 O-Ring is a precision chassis sealing component built for SINOTRUK Howo trucks, providing a reliable fluid-tight seal at critical joints in the chassis, brake and driveline systems. As a trusted supplier of genuine Sinotruk howo parts, we offer this OEM-grade O-Ring as a direct replacement for the factory original. The WG295420033 ring ensures correct compression, long sealing life and dependable operation on Howo A7, T7H, HOWO 371 and HOWO 380 models.
Manufactured from high-quality synthetic rubber with excellent resistance to oil, diesel, water, heat and ageing, the O-Ring is molded to exact OEM dimensions. Its precise cross-section and inner diameter maintain correct squeeze, resist vibration, pressure spikes and temperature extremes, and perform reliably in constant commercial truck service.
OEM WG295420033 • Chassis sealing ring • Oil and diesel resistant • Heat resistant • Direct OEM fit
The WG295420033 O-Ring is a circular elastomer seal installed in a machined groove between two mating chassis components. When the parts are tightened together, the ring is compressed and forms a barrier that prevents oil, diesel, water or air from escaping.
This WG295420033 ring is molded to exact OEM dimensions. Inner diameter, cross-section, hardness and surface finish all match the factory specification, so it seats correctly in the groove and delivers consistent sealing pressure across the joint.
Common signs that an O-Ring needs replacement include visible fluid leaks at the joint, a swollen or hardened ring, cracks or cuts in the rubber, a flattened cross-section that no longer seals, and fluid weeping that leaves a film or drip on the housing.
Fitting a new WG295420033 O-Ring restores a reliable fluid-tight seal, stops leaks and protects internal components from contamination and fluid loss. It is a small, low-cost part that plays a critical role in chassis reliability.
The WG295420033 O-Ring fits SINOTRUK Howo trucks, mainly the A7, T7H, HOWO 371 and HOWO 380 series. It is a direct OE replacement, so it seats into the original machined groove and works with the factory mating components.
This O-Ring is used in long-haul transport, construction, mining, logging and municipal service. In these roles, it must hold a reliable seal despite vibration, pressure changes, heat, dust, mud and water while the truck operates under heavy load.
When fitting the WG295420033, inspect the groove, mating surfaces, bolts and adjacent seals for damage or wear. A scored groove or warped flange can cause a new O-Ring to leak, so checking these areas saves time and avoids repeat repairs.
For fleets running multiple HOWO trucks, keeping the WG295420033 O-Ring in stock makes chassis sealing repairs faster and more predictable, reducing downtime and keeping vehicles leak-free and on the road.
Replacing the WG295420033 O-Ring is a job for a qualified technician using basic hand tools. Clean the work area first so dirt cannot enter the joint. Drain the fluid if the seal is below the fluid level.
Separate the mating parts, remove the old ring with a soft pick, and inspect the groove and surfaces for nicks, burrs, corrosion or old sealant. Clean the groove thoroughly and wipe it dry before fitting the new ring.
Lubricate the new O-Ring with a small amount of clean system fluid, then seat it evenly in the groove without twisting it. Reassemble the parts and tighten the bolts to the OEM torque in a cross pattern.
Refill the fluid, run the system and check for leaks at the joint. During routine service, inspect the O-Ring for swelling, hardening, cuts or flattening and replace it whenever the joint is opened for other repairs.
The WG295420033 O-Ring is produced in an ISO 9001-certified plant using high-quality synthetic rubber compound. Incoming rubber is checked for hardness, tensile strength and resistance to oil, diesel and heat before molding begins.
Each ring is molded on precision equipment, then inspected for inner diameter, cross-section, roundness and surface finish. Every batch is dimensionally checked, and samples receive a compression and recovery test before packing.
Batch samples undergo fluid immersion, thermal cycling, ozone exposure and ageing tests to confirm long-term sealing reliability in heavy-duty truck use. These checks help ensure the O-Ring performs in the tough conditions Howo trucks face every day.
The WG295420033 is covered by a 12-month warranty against material and workmanship defects. Strict quality control means every O-Ring matches the fit, function and durability of the original factory part.
The O-Ring helps maintain a fluid-tight seal, prevents leaks and protects internal chassis components on your Howo truck. A worn or damaged O-Ring can cause fluid loss, contamination and damage to expensive driveline or brake parts.
Made from quality synthetic rubber with excellent fluid and heat resistance, the WG295420033 offers dependable sealing performance and long service life. Its exact OEM dimensions keep installation simple and work with the factory machined groove.
Fleet managers gain shorter repair times, lower maintenance costs and better vehicle availability. Owner-operators get confidence from an O-Ring that meets strict OEM standards and is backed by a 12-month warranty.
Choose the WG295420033 O-Ring for your SINOTRUK Howo and keep your chassis joints sealed, dry and reliable for the long haul.
We are a first-class heavy duty vehicles and spare parts supplier in China. which covers from engine, gearbox, cab, axle assemblies to main assembly accessories, electrical parts and other chassis parts like brake, clutch and steering parts.
A PROFESSIONAL CHINA TRUCK AND SPARE PARTS SUPPLIER
@Copyright DERUNA
