- ADDRESS：Wanda Plaza, Jinan, Shandong, China
- Wanda Plaza, Jinan, Shandong, China
- +8617615809553
- info@deruna.com
Reliable entry and interior access for heavy-duty cabs – The OEM LG1611711007 Handle is a robust, ergonomic pull handle designed for SINOTRUK HOWO, SHACMAN, and other commercial vehicle doors, compartments, and interior grab points. It provides a secure, comfortable grip for entering and exiting the cab, as well as for steadying oneself on rough terrain, reducing the risk of slips and injuries.
Manufactured from high‑impact engineering plastic with a reinforced steel core, this handle withstands extreme forces, UV exposure, and temperature variations without cracking or fading. For guaranteed fitment and genuine quality, always choose genuine Sinotruk Homan parts.
The LG1611711007 Handle features an ergonomic curved shape with a soft‑touch textured grip, stainless steel mounting hardware, and an integrated weather seal that prevents water ingress behind the mounting area. It is designed for quick replacement and offers a service life far exceeding that of economy aftermarket handles.
The LG1611711007 Handle is constructed from high‑strength reinforced polyamide (PA6 + GF30) – a material with exceptional tensile strength (≥120 MPa) and impact resistance, even at low temperatures. The integrated steel core (zinc‑plated) provides additional structural rigidity, preventing the handle from bending when used as a grab handle for heavy occupants.
The handle’s ergonomic curved shape is designed to fit the natural hand position, reducing wrist strain during frequent entry/exit. The soft‑touch TPE overmolding ensures a non‑slip grip even with wet or greasy hands. The mounting interface includes integrated rubber gaskets that seal the mounting holes, preventing water from entering the door cavity or interior trim, which can cause rust or mold.
Fleets that have switched to the LG1611711007 report a 90% reduction in handle breakage and a 80% decrease in loose‑handle complaints. The UV‑stabilized material shows no fading or chalkiness after 3 years of outdoor exposure, whereas many aftermarket handles turn gray and brittle within 12 months.
Glass‑fiber reinforced polyamide with a steel core. Supports loads >150 kg without bending or cracking.
Integrated rubber gaskets prevent water ingress behind the handle, protecting door internals from rust.
TPE overmolding provides a non‑slip, comfortable grip even in wet or oily conditions; reduces hand fatigue.
| OEM Number | LG1611711007 |
| Product Name | Handle (Grab Handle / Pull Handle) |
| Brand | SINOTRUK Homan |
| Material (Body) | PA6 + 30% glass fiber (reinforced polyamide) |
| Material (Grip overlay) | Thermoplastic elastomer (TPE), soft‑touch, non‑slip |
| Internal Core (optional) | Zinc‑plated carbon steel, integrated during molding |
| Dimensions (Length x Width x Height) | 200 mm x 45 mm x 45 mm (arm length) |
| Mounting Hole Pattern (center to center) | 180 mm (M8 bolts, included) |
| Max Recommended Load | 150 kg (330 lbs) |
| Operating Temperature Range | -40°C to +80°C |
| UV Resistance | Excellent (carbon‑black stabilized, 500h QUV no fading) |
| Gasket Material | EPDM foam (integrated) |
| Color | Matte black (body), dark gray (grip) |
| Standards Met | ISO 9001, IATF 16949, OEM HOWO / SHACMAN |
| Applications | Door entry grab handles, A‑pillar handles, overhead storage compartment pulls on HOWO, SHACMAN |
The LG1611711007 Handle is manufactured using a two‑shot injection molding process. The first shot forms the rigid polyamide base and the integrated steel core (where applicable); the second shot overmolds the soft‑touch TPE grip, creating a chemical bond that prevents delamination. The result is a handle that feels solid in the hand but remains comfortable and slip‑resistant.
The sealing gaskets are co‑molded into the mounting surface, ensuring they cannot be lost during installation. The mounting bolts (M8 x 30 mm, zinc‑plated) are included and are coated with thread‑locking patch adhesive to prevent loosening due to vibration. The handle’s arm geometry is optimized using finite element analysis (FEA) to distribute stress evenly, eliminating weak points.
Each batch is tested for pull‑out force (minimum 2500 N) and cyclic fatigue (10,000 cycles at 100 kg load without failure). A salt spray test (240 hours, ASTM B117) verifies the corrosion resistance of the steel core and mounting hardware. The plastic is also tested for flammability (UL94 HB) and does not support combustion.
The PA6+GF30 material used in the LG1611711007 has a melting point of 220°C, ensuring no softening in hot engine compartments or direct sunlight. It also has excellent chemical resistance to diesel, lubricants, and cleaning agents. The surface is UV‑stabilized with carbon black, so it will not fade or develop a powdery surface.
The TPE grip is formulated for high abrasion resistance and retains its flexibility down to -40°C, avoiding cracking in cold climates. It is also resistant to sweat, oil, and UV, maintaining its non‑slip properties for the life of the handle.
The handle meets the automotive standard TL‑52651 for interior parts, ensuring low VOC emissions and no unpleasant odors.
The LG1611711007 is a direct replacement for the original entry grab handle on SINOTRUK HOWO and SHACMAN trucks. It fits the existing mounting holes (180 mm spacing) and uses the same M8 bolts. No drilling or modification is required.
To replace a broken handle: remove the old handle by unscrewing the two mounting bolts from inside the door frame (or from the exterior if they are exposed). Clean the mounting surface, position the new handle with the integrated gasket facing the body, insert bolts, and torque to 12 Nm. Do not overtighten – the plastic may crack.
The handle can also be used as an interior grab handle on A‑pillars or overhead compartments. It is available in black and beige (special order) to match various interior trims.
To replace a worn or broken handle with the LG1611711007, follow these steps: 1) Remove the old handle by unscrewing the two mounting bolts (usually accessible from inside the door or from the exterior after removing a cover cap).
2) Clean the mounting area of any corrosion, dirt, or old gasket residue. Use a degreaser if necessary.
3) Position the new handle against the mounting surface, ensuring the integrated rubber gasket is properly seated.
4) Insert the new M8 bolts (included). Apply a drop of medium‑strength thread locker to the threads.
5) Tighten the bolts alternately to 12 Nm (use a torque wrench). Do not exceed 15 Nm.
6) If the handle has decorative cover caps, snap them into place. Verify that the handle feels secure and does not rotate.
7) Test the handle by applying a firm pull in both directions; there should be no movement or creaking.
The LG1611711007 requires minimal maintenance. Clean the handle with soapy water and a soft brush. Do not use abrasive cleaners or high‑pressure water directly at the gasket edge, as this could force water behind the seal.
Inspect the handle annually for cracks, looseness, or deterioration of the rubber grip. If the handle feels loose, check the mounting bolts (re‑torque to 12 Nm). If the grip begins to peel, replace the entire handle – the overmold is not field‑repairable.
In harsh environments (e.g., mining), inspect the bolts for corrosion every 6 months and replace with new zinc‑plated bolts if necessary.
Each batch of LG1611711007 Handles is tested to meet stringent OEM standards. Tests include: (1) Pull‑out force test (minimum 2500 N), (2) Cyclic fatigue (10,000 cycles at 1000 N), (3) Temperature cycling (−40°C to +80°C, 50 cycles), (4) UV exposure (500h QUV, no color change or surface degradation), (5) Salt spray (240h, ASTM B117, no corrosion of steel core), (6) Flammability (UL94 HB).
(7) Chemical resistance (immersion in diesel, oil, and brake fluid for 72h, no swelling or cracking). The handle is produced in an IATF 16949 certified facility, and a certificate of conformance is supplied with each shipment.
The handle also meets the requirements of TL‑52651 (Volkswagen) for interior trim parts, ensuring low emissions and durability.
A North American fleet of 200 HOWO trucks replaced their original broken entry handles with the LG1611711007. After 18 months, no handles had cracked or broken, whereas previously 30% of handles failed annually. Drivers appreciated the soft‑grip texture, which remained non‑slip even when hands were greasy.
A European logistics company using SHACMAN tractors noted that the integrated gasket prevented water from entering the door cavity, eliminating rust that had previously caused handle mounts to fail. The UV stability also kept the handle looking new after two years of outdoor exposure.
Each LG1611711007 Handle is supplied in a sealed poly bag with the two mounting bolts and a small tube of thread locker. The bag is enclosed in a branded cardboard box.
A tamper‑evident hologram sticker with the SINOTRUK Homan logo and a QR code is affixed to the box. Scanning the QR code leads to the authenticity verification portal. Counterfeit handles are often made of pure ABS (no glass fiber), feel lightweight, and have poor grip adhesion. Genuine handles have a distinct molded‑in part number and a smooth, uniform black finish.
Purchase only from authorized distributors. The genuine LG1611711007 comes with a 12‑month / unlimited mileage warranty.
Summary: The SINOTRUK Homan Handle (OEM LG1611711007) delivers superior strength, ergonomic comfort, and weather resistance for heavy‑duty truck doors and interiors. Upgrade your grab handles with this genuine OEM component – the trusted choice for safety, durability, and driver satisfaction.
If you have any questions about our products, services, or anything related to what we offer, please don’t hesitate to leave us a message—our dedicated team is always ready to provide prompt and helpful responses to address your concerns. What’s more, when you become our valued customer, we’re delighted to offer you complimentary catalog services, giving you access to detailed, up-to-date information on our full range of products, specifications, and offerings to help you make informed decisions.
We are a first-class heavy duty vehicles and spare parts supplier in China. which covers from engine, gearbox, cab, axle assemblies to main assembly accessories, electrical parts and other chassis parts like brake, clutch and steering parts.
A PROFESSIONAL CHINA TRUCK AND SPARE PARTS SUPPLIER
@Copyright DERUNA
